A potentiometer (pronounced /pətɛntʃi:ˈjɔmɪtə/ and colloquially known as a "pot") is a three-terminal resistor with a sliding contact that forms an adjustable voltage divider.[1] If only two terminals are used (one side and the wiper), it acts as a variable resistor or rheostat. Potentiometers are commonly used to control electrical devices such as volume controls on audio equipment. Potentiometers operated by a mechanism can be used as position transducers, for example, in a joystick. Potentiometers are rarely used to directly control significant power (more than a watt), since the power dissipated in the potentiometer would be comparable to the power in the controlled load (see infinite switch). Instead they are used to adjust the level of analog signals (e.g. volume controls on audio equipment), and as control inputs for electronic circuits. For example, a light dimmer uses a potentiometer to control the switching of a TRIAC and so indirectly control the brightness of lamps.
The slide-wire potentiometer was invented by Johann Christian Poggendorff (1796–1877) in 1841.[2] Leeds and Northrup Type K model was a standard piece of apparatus in most college and university electrical measurements laboratories for the first half of the 20th century. Potentiometer construction A potentiometer is constructed with a resistive element formed into an arc of a circle, and a sliding contact (wiper) travelling over that arc. The resistive element, with a terminal at one or both ends, is flat or angled, and is commonly made of graphite, although other materials may be used. The wiper is connected through another sliding contact to another terminal. On panel potentiometers, the wiper is usually the center terminal of three. For single-turn potentiometers, this wiper typically travels just under one revolution around the contact. "Multiturn" potentiometers also exist, where the resistor element may be helical and the wiper may move 10, 20, or more complete revolutions, though multiturn potentimeters are usually constructed of a conventional resistive element wiped via a worm gear. Besides graphite, materials used to make the resistive element include resistance wire, carbon particles in plastic, and a ceramic/metal mixture called cermet. One form of rotary potentiometer is called a String potentiometer. It is a multi-turn potentiometer operated by an attached reel of wire turning against a spring. It is used as a position transducer. In a linear slider potentiometer, a sliding control is provided instead of a dial control. The resistive element is a rectangular strip, not semi-circular as in a rotary potentiometer. Due to the large opening slot or the wiper, this type of potentiometer has a greater potential for getting contaminated. Potentiometers can be obtained with either linear or logarithmic relations between the slider position and the resistance (potentiometer laws or "tapers"). A letter code ("A" taper, "B" taper, etc.) may be used to identify which taper is intended, but the letter code definitions are variable over time and between manufacturers. Manufacturers of conductive track potentiometers use conductive polymer resistor pastes that contain hard wearing resins and polymers, solvents, lubricant and carbon – the constituent that provides the conductive/resistive properties. The tracks are made by screen printing the paste onto a paper based phenolic substrate and then curing it in an oven. The curing process removes all solvents and allows the conductive polymer to polymerize and cross link. This produces a durable track with stable electrical resistance throughout its working life.[citation needed] Linear taper potentiometer A linear taper potentiometer has a resistive element of constant cross-section, resulting in a device where the resistance between the contact (wiper) and one end terminal is proportional to the distance between them. Linear taper describes the electrical characteristic of the device, not the geometry of the resistive element. Linear taper potentiometers are used when an approximately proportional relation is desired between shaft rotation and the division ratio of the potentiometer; for example, controls used for adjusting the centering of (an analog) cathode-ray oscilloscope. Logarithmic potentiometer A logarithmic taper potentiometer has a resistive element that either 'tapers' in from one end to the other, or is made from a material whose resistivity varies from one end to the other. This results in a device where output voltage is a logarithmic function of the mechanical angle of the potentiometer. Most (cheaper) "log" potentiometers are actually not logarithmic, but use two regions of different resistance (but constant resistivity) to approximate a logarithmic law. A logarithmic potentiometer can also be simulated (not very accurately) with a linear one and an external resistor. True logarithmic potentiometers are significantly more expensive. Logarithmic taper potentiometers are often used in connection with audio amplifiers as human perception of audio volume is logarithmic. Rheostat The most common way to vary the resistance in a circuit is to use a variable resistor or a rheostat[3] A rheostat is a two-terminal variable resistor. Often these are designed to handle much higher voltage and current. Typically these are constructed as a resistive wire wrapped to form a toroid coil with the wiper moving over the upper surface of the toroid, sliding from one turn of the wire to the next. Sometimes a rheostat is made from resistance wire wound on a heat-resisting cylinder with the slider made from a number of metal fingers that grip lightly onto a small portion of the turns of resistance wire. The "fingers" can be moved along the coil of resistance wire by a sliding knob thus changing the "tapping" point. They are usually used as variable resistors rather than variable potential dividers. Any three-terminal potentiometer can be used as a two-terminal variable resistor by not connecting to the third terminal. It is common practice to connect the wiper terminal to the unused end of the resistance track to reduce the amount of resistance variation caused by dirt on the track. Digital potentiometer A digital potentiometer is an electronic component that mimics the functions of analog potentiometers. Through digital input signals, the resistance between two terminals can be adjusted, just as in an analog potentiometer. Membrane Potentiometer A membrane potentiometer uses a conductive membrane that is deformed by a sliding element to contact a resistor voltage divider. Linearity can range from 0.5% to 5% depending on the material, design and manufacturing process. The repeat accuracy is typically between 0.1mm and 1.0mm with a theoretically infinite resolution. The service life of these types of potentiometers is typically 1 million to 20 million cycles depending on the materials used during manufacturing and the actuation method; contact and contactless (magnetic) methods are available. Many different material variations are available such as PET(foil), FR4, and Kapton. Membrane potentiometer manuafacturers offer linear, rotary, and application-specific variations. The linear versions can range from 9mm to 1000mm in length and the rotary versions range from 0° to 360°(multi-turn), with each having a height of 0.5mm. Membrane potentiometers can be used for position sensing.[4] Potentiometer applications Potentiometers are widely used as user controls, and may control a very wide variety of equipment functions. The widespread use of potentiometers in consumer electronics has declined in the 1990s, with digital controls now more common. However they remain in many applications, such as volume controls and as position sensors. Audio control One of the most common uses for modern low-power potentiometers is as audio control devices. Both linear potentiometers and rotary potentiometers are regularly used to adjust loudness, frequency attenuation and other characteristics of audio signals. The 'log pot' is used as the volume control in audio amplifiers, where it is also called an "audio taper pot", because the amplitude response of the human ear is also logarithmic. It ensures that, on a volume control marked 0 to 10, for example, a setting of 5 sounds half as loud as a setting of 10. There is also an anti-log pot or reverse audio taper which is simply the reverse of a logarithmic potentiometer. It is almost always used in a ganged configuration with a logarithmic potentiometer, for instance, in an audio balance control. Potentiometers used in combination with filter networks act as tone controls or equalizers. Television Potentiometers were formerly used to control picture brightness, contrast, and color response. A potentiometer was often used to adjust "vertical hold", which affected the synchronization between the receiver's internal sweep circuit (sometimes a multivibrator) and the received picture signal. Transducers Potentiometers are also very widely used as a part of displacement transducers because of the simplicity of construction and because they can give a large output signal. Computation In analog computers, high precision potentiometers are used to scale intermediate results by desired constant factors, or to set initial conditions for a calculation. A motor-driven potentiometer may be used as a function generator, using a non-linear resistance card to supply approximations to trigonometric functions. For example, the shaft rotation might represent an angle, and the voltage division ratio can be made proportional to the cosine of the angle. Theory of operation The potentiometer can be used as a voltage divider to obtain a manually adjustable output voltage at the slider (wiper) from a fixed input voltage applied across the two ends of the potentiometer. This is the most common use of them. The voltage across RL can be calculated by: VL = VS * R2 RL / ( R1 RL + R2 RL + R1 R2) . If RL is large compared to the other resistances (like the input to an operational amplifier), the output voltage can be approximated by the simpler equation: VL = VS * R2 / ( R1 + R2 ) As an example, assume VS = 10 V , R1 = 1 kΩ, R2 = 2ΩΩ, and RL = 100Ω . Since the load resistance is large compared to the other resistances, the output voltage VL will be approximately: 10V * 2 k Ω / 1 kΩ + 2 kΩ ) = 2/3 * 10 V = 6.666...V. Due to the load resistance, however, it will actually be slightly lower: ≈ 6.623 V. One of the advantages of the potential divider compared to a variable resistor in series with the source is that, while variable resistors have a maximum resistance where some current will always flow, dividers are able to vary the output voltage from maximum (VS) to ground (zero volts) as the wiper moves from one end of the potentiometer to the other. There is, however, always a small amount of contact resistance. In addition, the load resistance is often not known and therefore simply placing a variable resistor in series with the load could have a negligible effect or an excessive effect, depending on the load. Early patents US patent 131,334, Thomas Edison, "Coiled resistance wire rheostat", issued 1872-9-17
Potentiometric sensor
^ The Authoritative Dictionary of IEEE Standards Terms (IEEE 100) (seventh edition ed.). Piscataway, New Jersey: IEEE Press. 2000. ISBN 0-7381-2601-2. Retrieved from "http://en.wikipedia.org/" |
|
